רמקול עמוד אקטיבי , 500W, עם סאב 8x2" מבית PURE ACOUSTICS

OPERATIONS MANUAL – TU 80

Professional ABS Molded Loudspeaker
Introduction:
Congratulations on your purchase of the TU 80 multi-function, engineered and manufactured by us. The TU 80 includes a
high-output compression driver, and 8” x 2 woofer that produces an even and smooth studio quality sound in a sound reinforcement
speaker. Our design goal was to build a speaker with accurate playback, smooth dispersion of mid and high
frequencies, and an ergonomic design for easy transport and setup. The result is a sound reinforcement system dynamic
enough to use at home, in the studio, parties or in a home theater.

Features:

1. 2-way Active Speaker.
2. Steel basket woofer
3. High wattage powered amplifier
4. Auxiliary line input
5. High Temperature Voice Coil
6. Bluetooth Stereo Pairing
7. DSP Processer
8. USB Charging

Important Safety Instructions:

1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers)
that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one
wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third
prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement
of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the tripod sold with the apparatus.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Failing to adhere to the cautions above will void the manufacturer warranty!
connect with your device.
Freq Resp: 50Hz-18KHz
RMS Power: 500W
MAX Power: 1500W
MAX SPL: 119.5 dB
Impedance: 4 Ohm
TU 80 connect with your device.

Functions:

1. USB Port
2. Bluetooth Stereo Function.
3. Mic level: Control the signal for Mic input when using the Mic input.
4. Line Level: Control the ouput volume for Line Level Input.
5. Aux level: Control the signal for Aux input when using the Aux input.
6. Sub Level: Adjust the overall level available from the subwoofer.
7. Main Level: Overall level adjustment. The sub level is also adjusted in accordance with the
preset level oh the Sub Level controller.
8. Mic/Inst Input: These balanced inputs accepts a standard XLR and a 1/4” Jack phone plug.
A board range of signals from microphones, audio mixing consoles and electronic musical
instruments may be connected here.
9. Line Input left: Use XLR and a 1/4” jack connector balanced or unbalance.
10. Line Input right: Use XLR and a 1/4” jack connector balanced or unbalance.
11. Aux Input: Use RCA and 3.5mm connector balanced or unbalance.
12. Mix Out: Use XLR connector balanced or unbalanced.
13. INDICATOR LEDS
ON: Lights up once the system is properly connected to the power mains and switched on.
SIGNAL: Lights up as soon as an audio signal is present. The signal acquisition is performed
before the MAIN LEVEL controller.
LIMIT: Lights up if the loudspeaker system is operating in the clipping range. A short flash of
the LED is not critical. To protect the system, an excessive signal level is gently turned down
by the built-in limiter. If the limiter LED lights up permanently or for longer periods, reduce
the volume level. Failure to do so may result in a distorted sound and damage to the
speaker system.
14. Power Supply Input Connector: Use with power cord.
15.????Power Supply Switch

Warning: Make sure speaker is off and all LEVEL controls are down (counterclockwise) before every use.

1.Connect the output from your signal source (mixing console, microphone, preamp, or other mic- or line-level source) directly to the INPUT connector

on the back of the speaker. It accepts balanced line-level signals from mixers, preamplifiers, CD players, tape decks, etc., and accepts direct connections
from dynamic microphones through the MIC input.
2.There is also an XLR Output connector labeled LINE OUT. This allows you to connect more than one TU 80 to the output of your sound source. Simply
plug an XLR cable from the Line Out connector of one speaker to the input connector of another speaker, and so on, daisy-chaining multiple speakers.
3.Turn on your signal source. (Make sure volume is turned down) Turn on TU 80. Start signal source and adjust volume controls on the signal source and

TU 80 speaker.
Bluetooth Pairing instructions:

1. Press and hold Pair button for 3 seconds until speaker beeps and blue pairing indicator flash’ s.
2. While pairing light is flashing push quickly once the pairing button again and connect with your pairing device.
3. Connect on your pairing device to complete pairing to the TU 80.
Bluetooth Stereo Function Usage:

1. The PAIR button has the function of Pairing and On-Off. Press and hold it for 3 seconds to turn on the Bluetooth.
2. Press and release PAIR button on one speaker only, this TU 80 will be left channel.
3. Connect with your device.
4. Press and release STEREO LINK button on each speaker, both speakers should be TU 80 and the other TU 80 will be right channel.
5. Press and hold STEREO LINK button for 3 seconds to exit the connection.
NOTE: Only exit after connected successfully.
6. LEDs flash while pairing or linking. LEDs light solid when paired or linked.
7. To reset pairing and linking, press and hold either button for 2 seconds.
NOTE: Initial pairing or linking may require 1 minute.

סיריוס אלקטרוניקה מתחייבת לאיכות גבוהה של מוצריה ולשירות הטוב ביותר ללקוחותיה.

במידה והתחרטתם או מכל סיבה שהיא אינכם מרוצים, תוכלו להחזיר את המוצר שרכשתם תוך 14 ימי עסקים מיום הרכישה, כאשר המוצר ארוז  על כל חלקיו באריזתו המקורית ובצירוף קבלה מקורית.

אנו נחליף לכם את המוצר או נשיב לכם את כספכם לפי אופן התשלום בו בוצעה העסקה ובהתאם למדיניות הביטולים, ההחזרות וההחלפות של החברה.

לתשומת לבכם, מוצרים בעלי אופן שימוש אישי כגון אוזניות או זרועות, מתקני תלייה או ארוניות שהורכבו, או מוצרים מוצרים שנעשה בהם שינוי או תיקון - אינם נכללים במדיניות ההחלפות וההחזרות.

סיריוס אלקטרוניקה שומרת לעצמה את הזכות שלא להחליף מוצר או לזכות בגינו במידה ואינו עומד בתנאי מדיניות ההחלפות וההחזרות של החברה.